This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

The maximum mass of dry textile material in kilograms to be used in the appliance.

The dryer shall not be connected to the power mains using an extension cord.

Do not connect the tumble dryer to an electrical outlet intended for an electric shaver or a hair dryer.

The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted.

The air in the room where the dryer is installed may not contain dust particles.

Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.

Install the dryer in a room with adequate ventilation and a temperature between 15°C and 25°C.

Do not dry unwashed items in the tumble dryer.

Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.

Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.

Never block the air exhaust (evacuation opening).

For appliances with ventilation openings in the base, a carpet must not obstruct the openings.

The lint must not to be allowed to accumulate around the tumble dryer.

Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.

That the lint filter has to be cleaned frequently, if applicable.
Clean the dryer filters after each drying cycle. If you have removed the filters, replace them before the next drying cycle.

Do not use any solvents or cleaning agents that could damage the dryer (please observe the recommendations and warnings provided by the manufacturers of the cleaning agents).

Never add chemicals or fragrances into the condensate tank (see chapters ; / ).

After the drying process, unplug the dryer power cord from the power outlet.

The warranty does not cover consumables, minor deviations in colour, increased noise that results from appliance age and which does not affect the functionality of the dryer, and aesthetic defects on components, which do not affect the dryer's functionality and safety.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Only use the dryer to dry laundry that was washed with water. Do not dry any laundry that was washed or cleaned with flammable cleaners or substances (such as gasoline, trichloroethylene etc.) as this may result in an explosion.

The tumble dryer is not to be used if industrial chemicals have been used for cleaning.

The dryer is protected with an automatic switch-off system in case of overheating. This system will switch off the dryer if the temperature is too high.

If the net filter is clogged, the overheating automatic switch-off system may be activated. Clean the filter, wait for the dryer to cool down, and try running it again. If the dryer still fails to start, call a service technician.

Do not damage the refrigerant circuit.

The refrigerant R290 in this appliance is environmentally friendly yet combustible and may ignite if it comes into contact with open flames or ignition sources. Keep naked flames and ignition sources away from the appliance.

	Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately.
The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. Take the product to an authorized collection centre for waste electric and electronic equipment processing.
When disposing of the appliance at the end of its useful life, remove all power cords, and destroy the door latch and switch to prevent the door from locking or latching (child safety).
Correct disposal of the product will help prevent any negative effects on the environment and health of people, which could occur in case of incorrect product removal. For detailed information on removal and processing of the product, please contact the relevant municipal body in charge of waste management, your waste disposal service, or the store where you bought the product.

The control unit is located on the upper right part of the appliance. With it, you will be able to control the operation of the appliance: - switch the appliance on or off, - select the drying programme and additional options, - adjust additional appliance settings, - start and stop the programme cycle, - identify possible malfunctions and errors, and perform basic troubleshooting.
1	Selection and confirmation button (hereinafter referred to as the selector) To select a program, rotate the selector to the desired program. See chapter / / To confirm the selection, press the selector.
2	Button for switching the appliance on and off To turn the appliance on or off, press On/Off.
3	Key Start/Pause (lights up when active) To start, pause, or resume a program, press key Start/Pause.
4	Function key Settings
5	Colour display (referred to as the screen or display) Main menu set / Advanced settings in the menu / Submenu set
6	Function key Extras
7	Function key Back
8	Function key Half load

The table lists all menus and submenus available on the appliance.
Before using the appliance for the first time, you will need to select certain initial settings, such as Language. See chapter / / .

You can access individual menus in one or more of the following ways:
- by turning the selector,
- by pressing the selector,
- by pressing one of the function keys.

Confirm the selection by pressing the selector.

Follow the instructions on the screen.

The display provides the following information:

Initial settings before use Language Drain method Tank Drain Skip Connect device to Wi-Fi Wi-Fi Yes / Finish setup Open the ConnectLife app Knob for selection and confirmation (1) Program selection (press the selector) Modes Disinfect / Nature dry / Default Dry target Iron / Storage / Extra dry Anti crease On / Off

Extras (6) Child Lock Remote control Delay end Save changes  Settings (4) Dry laundry Remote control Settings Sound / Language / Display brightness / Manage programs / Wi-Fi settings / Drain method / Reset to default/ Factory reset / Wash&Dry sync alerts Information Statistics / Cycles Statistics / Errors   Half load (8)

From 1 March 2021, information on energy labelling and ecodesign requirements is available in the EU EPREL product database.

The QR code on the energy label supplied with the appliance contains a web link through which you can find your registered appliance in the EU EPREL database.
Information regarding the performance of the product can also be found in the EU EPREL database, which is accessible via the link https://eprel.ec.europa.eu where you have to enter the model and product number; both are indicated on the rating plate on the appliance. On the website www.theenergylabel.eu you can find more detailed information about the energy label.

Keep the energy label in case it is needed in the future, together with the user manual and other documents supplied with this appliance.

The company declares that the device with the function ConnectLife complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The detailed Declaration of Conformity can be found at the web address https://auid.connectlife.io on the page of your device among the additional documents.

Use a reliable wireless connection with sufficient signal strength. For all connection requirements, see the detailed instructions online.

If the dryer has to be laid down on one of the sides during transport or servicing, place it with its right side, viewing from the appliance front, downwards. Never turn the dryer upside down or lay it on its back or front!

If the condensate water tank is full and needs to be emptied, The water tank is full is displayed on the screen. Empty the condensate water tank and confirm this by pressing the selector.

To avoid emptying the condensate tank, run the condensate discharge hose located at the back of the appliance directly into a drain.

Connect the dryer to a grounded power outlet. After installation, the wall outlet should be freely accessible. The outlet should be fitted with an earth contact (in compliance with the relevant regulations).

When you connect the appliance and switch it on for the first time, you can set Language, Drain method, Wi-Fi settings. Follow the instructions on the display.

You can find more detailed instructions online.

Sort the laundry by type and thickness of the fabric (see chapter / ).

When sorting laundry, see the table below and pay attention to the labels on the laundry.

Drying	Ironing
Drying on a flat surface	Steam ironing can permanently damage textiles.
Line dry	Ironing at maximum 200°C
Drying at a low temperature	Ironing at maximum 150°C
Drying at a high temperature	Ironing at maximum 110°C
Tumble drying not allowed	Ironing not allowed
Hang damp

Once you have selected a washing programme, you can also choose and adjust additional functions for certain programmes.
Some functions can also be selected and adjusted later, while the programme is running.

This is done in two or three steps:
- selecting the function,
- setting the function level, if the function allows it,
- activating the function.

If you do not want to select additional functions, press the Start/Pause button.

A	Once you have selected a drying programme using the selector knob, additional settings and functions appear on the right side of the display as submenus (e.g. Modes, Dry target, Anti crease, etc.) that can be selected for that programme and are highlighted. Turn the selector to scroll through a range of possible functions and settings.
B	To select or set an additional function, repeat the procedure described above. A set of possible functions and settings appears on the screen.
C	You can also select additional programs in the app ConnectLife. Follow the instructions in the app.

Close the dryer door and start the drying programme by pressing the Start/Pause button on the right side of the display.

At the end of the drying cycle, an audible signal is emitted and Program completed is displayed on the screen. If you have selected the Anti crease function, Anti crease and To complete press Stop ... are displayed alternately. To end the cycle, press Start/Pause. 5 min after the programme is completed, the appliance enters low standby mode (sleep mode).

SAVING PROGRAM SETTINGS Settings saved Function to save your settings for selected programs and functions.

ADAPTTECH AdaptTech Automatic function for saving frequently used programs and functions.

OTROŠKA ZAŠČITA Child Lock A safety feature. Press to enter the menu and select the Child Lock function. Confirm activation of the Child Lock function by pressing the selector. When you touch any button or use the selector, the display shows that the Child Lock function is active/on. To switch off (deactivate) the child lock, press and hold button for 3 sec.

NOČNI NAČIN Night Mode For selecting a drying mode without audible signals.

REMOTE CONTROL Remote control Function for remote control.

Press the button to enter the User Settings menu and select Settings. Use the selector to move through the available user settings.

When you reach the desired setting, rotate the selector left or right to move between the available options.

Press the selector inwards to enter the desired option; the setting will be saved and you will return to the previous settings level.

Press the button to exit.

You can change the following settings:

VKLOP/IZKLOP ZVOKA Sound On/Off Option to switch the sound on or off. If the sound is switched off, there will be no audible signal at the end of the drying programme.

JEZIK Language Option to change the language on the user interface.

SVETLOST ZASLONA Display brightness Option to adjust the display brightness.

UPRAVLJANJE PROGRAMOV Manage programs Display of programmes and editing their order.

WI-FI NASTAVITVE Wi-Fi settings Option to enable or disable the Wi-Fi connection.

NAČIN ODTOKA Drain method Option to set the condensate water drainage mode.

PONASTAVITEV NA PRIVZETO Reset to default Reset all appliance settings to default.

TOVARNIŠKE NASTAVITVE Factory reset Delete all settings and return to the factory settings.

SYNC ALERTS Wash&Dry sync (connection between washing and drying) Optimal selection of the drying program based on the washing program used.

SKUPNO ŠTEVILO CIKLOV Cycles Option to review the completed cycles of the appliance.

PREGLED NAPAK Errors Option to view the last detected dryer errors.

Clean both parts of the lint filter (a, b) after each drying cycle.

During cleaning, some water may be spilled. It is therefore recommended to place an absorbent cloth on the floor.

Warnings/information for the user, which can be indicated on the display unit, may include the following:

	Overview of the number of drying cycles performed The number of drying cycles performed will appear on the display for 3 seconds if you unplug the power cord, wait 10 seconds and then plug the power cord back in. After 3 seconds, the appliance enters standby mode.
	Full condensation water tank warning (The water tank is full) Empty the condensate tank before resuming the programme (see chapter / /).
PF	Power supply failure warning Drying interrupted due to power supply failure. Press the Start/Pause button to restart or resume the drying programme.
	Drying cycle completed warning (Empty water tank and clean filters / Clean filters) Clean the filters and empty the condensate tank. After the drying programme is completed, Empty water tank and clean filters is displayed on the screen. If the condensate drain hose is connected directly to a drain, Clean filters is displayed after drying.

The following lists all the errors that the user can see on the user interface.

E91 E92 E93	Temperature sensor failure
E0	Control unit failure
E2	Communication error
E3	Pump error Failure on the pump for pumping the condensate into the condensate tank
E7 E8	Control unit failure Disconnect the tumble dryer from the power supply.
TR isBPM E11	Error in BLDC motor communication No connection between the motor and the control unit.
TR isWIFI	The appliance cannot be controlled remotely Appliance remote control is not activated or enabled. Check if the Wi-Fi symbol on the appliance is lit, and turn the selector to position Remote control .
TR isWIFI	The appliance will not connect to the Wi-Fi network The appliance cannot find your Wi-Fi network. Check whether 2.4 GHz network is activated on your router and whether the Wi-Fi signal at the appliance is strong enough.
TR isWIFI E17	The appliance will not connect to the Wi-Fi network The error only affects the remote control functionality. It does not affect the drying process on other programmes.

Write down the error code (e.g. E0, E1), switch off the dryer, and call the nearest authorized service (call centre).

When you contact a service centre, please state your dryer's type, code/ID, model number, and serial number.

Dryer type, code, model, and serial number can be found on the rating (type) plate on the inner side of the dryer door.

A more detailed description of the rating plate can be found in the detailed instructions available online.

Splošna napisna tablica

MAJHEN PRESLEDEK

1 – type designation of the appliance 2 – model designation of the appliance 3 – the article number/service index (you will need them when contacting customer service) 4 – serial number of the appliance (you will need them when contacting customer service) 5 – unique QR code (required when connecting the appliance to a Wi-Fi network)

Your dryer is intended solely for household use. If the dryer is used for professional, for-profit purpose or purpose exceeding normal use in a household, or if the dryer is used by a person who is not a consumer, the warranty period shall be equal to the shortest warranty period required by relevant legislation.

Follow the instructions for correct installation of the Gorenje dryer and connection to the power mains (see chapter ).

All and any repairs or maintenance tasks on the dryer should only be done by trained experts. Unprofessional repair may result in an accident or major malfunction.

After installation, the dryer should stand still for two hours before it is connected to the power mains.

The dryer shall not be connected to the power mains using an extension cord.

Do not connect the tumble dryer to an electrical outlet intended for an electric shaver or a hair dryer.

In case of a defect, only use approved spare parts by authorized manufacturers.

In case of incorrect dryer connection, incorrect use, or servicing by an unauthorized person, the user shall bear the cost of any damage as such damage shall not be covered by warranty.

Always use the hoses supplied with the dryer.

Install the dryer in a room with adequate ventilation and a temperature between 15 °C and 25 °C.

At least two persons are required to install the tumble dryer on top of a washing machine.

Place the dryer on a level and stable solid (concrete) base.

The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted.

Never block the air exhaust (evacuation opening).

For appliances with ventilation openings in the base, a carpet must not obstruct the openings.

The air in the room where the dryer is installed may not contain dust particles.

Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.

The lint must not to be allowed to accumulate around the tumble dryer.

In the appliance enclosure or in the built-in structure, keep ventilation openings clear of obstruction.

The appliance may not be in contact with a wall or adjacent furniture.

After installation, wait for 24 hours before using the dryer. If the dryer has to be laid down on one of the sides during transport or servicing, place it with its right side, viewing from the appliance front, downwards.

Do not dry unwashed items of laundry in the tumble dryer.

Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.

Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.

Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.

If the condensate tube is blocked or clogged, then tumble dryer operation is stopped (see chapter /).

Before moving the dryer or before storing it in a non-heated room during the winter, the condensate tank has to be emptied.

That the lint filter has to be cleaned frequently, if applicable.
Clean the dryer filters after each drying cycle. If you have removed the filters, replace them before the next drying cycle.

Do not use any solvents or cleaning agents that could damage the dryer (please observe the recommendations and warnings provided by the manufacturers of the cleaning agents).

Never add chemicals or fragrances into the condensate tank (see chapters ; / ).

After the drying process, unplug the dryer power cord from the power outlet.

The dryer uses a heat pump system to heat the air.

The system consists of a compressor and a heat exchanger. When the dryer is started, compressor operation (the sound of flowing liquid) or flow of refrigerant may be louder as long as the compressor operates. This is not a sign of malfunction and it will not affect useful life of the dryer. In time and with use of the dryer this noise will become quieter.

The warranty does not cover consumables, minor deviations in colour, increased noise that results from appliance age and which does not affect the functionality of the dryer, and aesthetic defects on components, which do not affect the dryer's functionality and safety.

Prevent your children and pets from entering the dryer drum.

Before closing the dryer door and running the programme, make sure there is nothing except laundry in the drum (e.g. if a child climbed into the dryer drum and closed the door from the inside).

Activate the child lock. See chapter / / Child Lock.

The dryer is made in compliance with all relevant safety standards.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

The back of the dryer may get very hot during operation. Wait for the dryer to cool down completely before touching its back side.

If you open the dryer door during the drying process, the clothes may be very hot and there is a risk of burning.

Never stop the drying process before it is completed; if you do interrupt the cycle for any reason, be careful when removing the laundry from the drum as it is very hot. Quickly remove the laundry from the drum and spread it to allow it to cool down as quickly as possible.

The tumble dryer is not to be used if industrial chemicals have been used for cleaning.

The dryer is protected with an automatic switch-off system in case of overheating. This system will switch off the dryer if the temperature is too high.

If the net filter is clogged, the overheating automatic switch-off system may be activated. Clean the filter, wait for the dryer to cool down, and try running it again. If the dryer still fails to start, call a service technician.

Do not damage the refrigerant circuit.

The refrigerant R290 in this appliance is environmentally friendly yet combustible and may ignite if it comes into contact with open flames or ignition sources. Keep naked flames and ignition sources away from the appliance.

Once you have unpacked the appliance, we advise you to recycle all packaging materials. Dispose of them in the appropriate containers or take them to a local collection center.

to ensure your appliance works as efficiently and lasts as long as possible, we recommend that you:

• observe the recommended nominal load for each drying programme (see chapter /),

• ensure that the laundry is properly spun before drying,

• clean the appliance regularly (see chapter ).

This will help protect the environment and save natural resources.

	Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately.
The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. Take the product to an authorized collection centre for waste electric and electronic equipment processing.
When disposing of the appliance at the end of its useful life, remove all power cords, and destroy the door latch and switch to prevent the door from locking or latching (child safety).
Correct disposal of the product will help prevent any negative effects on the environment and health of people, which could occur in case of incorrect product removal. For detailed information on removal and processing of the product, please contact the relevant municipal body in charge of waste management, your waste disposal service, or the store where you bought the product.

FRONT 1 Start key Start/Pause 2 Colour display control unit 3 Button for switching the appliance on and off (On/Off) 4 Selection and confirmation button (hereinafter referred to as the selector) 5 Condense water tank 6 Rating plate 7 Door 8 Lint filter 9 Air vent 10 Heat exchanger		BACK 1 Power cord 2 Condensate discharge hose 3 Adjustable feet

a – width of the appliance: 600 mm b – height of the appliance: 850 mm c – depth of the appliance’s top surface: 625 mm d – depth with door closed: 655 mm e – depth with door open: 1110 mm

The depth of your dryer Gorenje is an important specification for possible stacking with a washing machine Gorenje. (See chapter /.)

1	The dryer door is hinged on the right side of the appliance and opens from the left side.
2	Place your hand in the recess on the top left side of the door. (The recess is not visible from the front.) When the dryer is stacked on top of the washing machine, use the recess on the bottom left side of the door to open. Pull the door towards you.
3	Close the door in reverse order until it locks into place.

The control unit is located on the upper right part of the appliance. With it, you will be able to control the operation of the appliance: - switch the appliance on or off, - select the drying programme and additional options, - adjust additional appliance settings, - start and stop the programme cycle, - identify possible malfunctions and errors, and perform basic troubleshooting.
1	Selection and confirmation button (hereinafter referred to as the selector) To select a program, rotate the selector to the desired program. See chapter / / To confirm the selection, press the selector.
2	Button for switching the appliance on and off To turn the appliance on or off, press On/Off.
3	Key Start/Pause (lights up when active) To start, pause, or resume a program, press key Start/Pause.
4	Function key Settings
5	Colour display (referred to as the screen or display) Main menu set / Advanced settings in the menu / Submenu set
6	Function key Extras
7	Function key Back
8	Function key Half load

The table lists all menus and submenus available on the appliance.
Before using the appliance for the first time, you will need to select certain initial settings, such as Language. See chapter / / .

You can access individual menus in one or more of the following ways:
- by turning the selector,
- by pressing the selector,
- by pressing one of the function keys.

Confirm the selection by pressing the selector.

Follow the instructions on the screen.

The display provides the following information:

Initial settings before use Language Drain method Tank Drain Skip Connect device to Wi-Fi Wi-Fi Yes / Finish setup Open the ConnectLife app Knob for selection and confirmation (1) Program selection (press the selector) Modes Disinfect / Nature dry / Default Dry target Iron / Storage / Extra dry Anti crease On / Off

Extras (6) Child Lock Remote control Delay end Save changes  Settings (4) Dry laundry Remote control Settings Sound / Language / Display brightness / Manage programs / Wi-Fi settings / Drain method / Reset to default/ Factory reset / Wash&Dry sync alerts Information Statistics / Cycles Statistics / Errors   Half load (8)