SAFETY PRECAUTIONS

knjiga Carefully read the instructions for use before using the washing machine.

Use in accordance with regulations

This appliance is intended to be used in household and similar applications, such as:

staff kitchen areas in shops, offices and other working environments;
farm houses;
by clients in hotels, motels and other residential type environments;
bed and breakfast type environments.

This appliance must not be used in:

areas for communal use in blocks of flats,
in open spaces or outdoors.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Installation and connection

The washing machine may only be used with the factory-installed power cord.

To avoid danger, a damaged power cord may only be replaced by the manufacturer, a service technician, or an authorized person.

Do not connect the washing machine to power mains using an external switching device such as a programme timer, or connect it to power mains that is regularly switched on and off by the power supply provider.

Connection to water and power supply has to be executed by an adequately trained technician or expert.

Any repair and maintenance pertaining to safety or performance should be done by trained experts.

Do not install the washing machine in a room where the temperature can drop to below 5°C, as washing machine parts may be damaged in case of water freezing.

The ventilation openings in the base of washing machine must not be obstructed by a carpet.

To connect the washing machine to water supply, make sure to use the supplied water supply hose and gaskets. Water pressure must be between 0,05 and 1 MPa (0,5–10 bar).

Always use a new water supply hose to connect the washing machine to water supply; do not reuse an old water supply hose.

The end of the water discharge hose should reach into a water drain line.

Before the start of the washing cycle, press the door on the indicated spot until it locks into place. The door cannot be opened during washing machine operation.

Proper use

We recommend that, before the first wash, you remove any impurities from the drum by using the Cotton white 90 °C program (see chapter / ).

After the washing cycle, close the water tap and pull out the washing machine plug from the power socket.

Only use the washing machine for washing laundry, as described in the instruction manual. The machine is not intended for dry cleaning.

Only use agents for machine washing and care of laundry. We shall not be responsible for any damages or discolouration of gaskets and plastic parts resulting from incorrect use of bleaching or colouring agents.

Do not use detergents that contain solvents as this could lead to release of poisonous gases, damage to the washing machine, and risk of fire and explosion.

When descaling, only use descaling agents with added anti-corrosion protection. (Only use non-corrosive descaling agents.) Follow the manufacturer's instructions. Finish the descaling process with several rinse cycles or by running the Ultra clean (Self-cleaning programme) in order to remove any residual acid (e.g. vinegar etc.).

Child safety

Warning – general danger

Children of less than 3 years should be kept away unless continuously supervised.

Children should be supervised to ensure that they do not play with the appliance.

The washing machine is made in compliance with all relevant safety standards.

Keep the detergent and conditioner out of reach of children.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance, shall not be made by children without supervision.

Danger of hot surface

Warning – danger of hot surface

At higher washing temperatures, the door glass will heat up. Be careful to avoid burns. Make sure children do not play near the door glass.

ENVIRONMENTAL PROTECTION

Once you have unpacked the appliance, we advise you to recycle all packaging materials. Dispose of them in the appropriate containers or take them to a local collection center.

Disposal of old appliance

	Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately.
The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. Take the product to an authorized collection centre for waste electric and electronic equipment processing.
When disposing of the appliance at the end of its useful life, remove all power cords, and destroy the door latch and switch to prevent the door from locking or latching (child safety).
Correct disposal of the product will help prevent any negative effects on the environment and health of people, which could occur in case of incorrect product removal. For detailed information on removal and processing of the product, please contact the relevant municipal body in charge of waste management, your waste disposal service, or the store where you bought the product.

Disposal of the end-of-life appliance

MAJHEN PRESLEDEK

DISPOSAL

	Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately.
The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. Take the product to an authorized collection centre for waste electric and electronic equipment processing.
When disposing of the appliance at the end of its useful life, remove all power cords, and destroy the door latch and switch to prevent the door from locking or latching (child safety).
Correct disposal of the product will help prevent any negative effects on the environment and health of people, which could occur in case of incorrect product removal. For detailed information on removal and processing of the product, please contact the relevant municipal body in charge of waste management, your waste disposal service, or the store where you bought the product.

WASHING MACHINE DESCRIPTION

Opis stroja - slika

FRONT

1	Start key (Start/Pause)
2	Touch control unit
3	Button for switching the appliance on and off (Off) and for programme selection (hereinafter referred to as the selector)
4	Detergent compartment
5	Rating plate
6	Door
7	Pump filter

BACK

1	Water inlet connector
2	Power cord
3	Water discharge hose
4	Hole for installing the protective plug
5	Adjustable feet

Opening and closing the washing machine door

Control unit


The control unit is located on the upper right part of the appliance. With it, you will be able to control the operation of the appliance: - switch the appliance on or off, - select the washing programme and additional options, - adjust additional appliance settings, - start and stop the programme cycle, - identify possible malfunctions and errors, and perform basic troubleshooting.
1	*Button for switching the appliance on and off and for programme selection (hereinafter referred to as the selector)* To select a program, rotate the selector to the desired program. See chapter / /
2	Symbol for switching the appliance on and off To switch on the appliance, rotate the selector to any position. To switch off the appliance, rotate the selector to the position .
3	Key Start/Pause (lights up when active) To start, pause, or resume a program, press key Start/Pause.
A	Additional settings symbols
B	Function keys
C	Display unit

The symbols light up when activated. The lighting can be full or partial.


4	Intensive
5	Saving
6	Silent
7	Extra water
8	Sound On/Off
9	Anti crease
10	Remote control
11	Steam
12	Child Lock
13	Settings saved
14	Dose aid
15	Tomato (option to set the type of stain)
16	Red wine (option to set the type of stain)
17	Grease (option to set the type of stain)

The function keys are finger-press-activated. Some functions can be selected by pressing two keys at the same time.

The 18, 20, 26, 27 keys are always visible. The other keys illuminate when in use.


18	Extras
19	Prewash
20	Modes
21	Add clothes
22	Ok
23	Fast
24	Draining water ...
25	Delay end
26	Stains
27	Settings

The display provides the following information:

washing temperature and spin speed,
various settings and animations, such as water hardness, sound level, etc.,
detergent dosage level and quantity,
remaining time until the end of the washing cycle,
information about malfunctions and error messages.


i 28 29	Temperature display Symbol Cold (lights up when active) Symbol Temperature (lights up when active)
ii 30 31	Spin speed display Symbol Rinse hold (lights up when active) Symbol Spin (lights up when active)
iii 32 33	Display for total washing time and/or delay end of washing Symbol ml (lights up when active) Symbol con. (lights up when active)

Izgled upravljalne enote

Control panel overview


The control unit is located on the upper right part of the appliance. With it, you will be able to control the operation of the appliance: - switch the appliance on or off, - select the washing programme and additional options, - adjust additional appliance settings, - start and stop the programme cycle, - identify possible malfunctions and errors, and perform basic troubleshooting.
1	*Button for switching the appliance on and off and for programme selection (hereinafter referred to as the selector)* To select a program, rotate the selector to the desired program. See chapter / /
2	Symbol for switching the appliance on and off To switch on the appliance, rotate the selector to any position. To switch off the appliance, rotate the selector to the position .
3	Key Start/Pause (lights up when active) To start, pause, or resume a program, press key Start/Pause.
A	Additional settings symbols
B	Function keys
C	Display unit

A-Simboli/B-Tipke/C-Prikazovalnik

A-Simboli GOR/HSN/UPO

Additional settings symbols 4-17

The symbols light up when activated. The lighting can be full or partial.


4	Intensive
5	Saving
6	Silent
7	Extra water
8	Sound On/Off
9	Anti crease
10	Remote control
11	Steam
12	Child Lock
13	Settings saved
14	Dose aid
15	Tomato (option to set the type of stain)
16	Red wine (option to set the type of stain)
17	Grease (option to set the type of stain)

B-TipkeGOR/HSN/UPO

Function keys 18-27

The function keys are finger-press-activated. Some functions can be selected by pressing two keys at the same time.

The 18, 20, 26, 27 keys are always visible. The other keys illuminate when in use.


18	Extras
19	Prewash
20	Modes
21	Add clothes
22	Ok
23	Fast
24	Draining water ...
25	Delay end
26	Stains
27	Settings

C-PrikazovalnikGOR/HSN/UPO

Display unit (i–iii, 28-33)

The display provides the following information:

washing temperature and spin speed,
various settings and animations, such as water hardness, sound level, etc.,
detergent dosage level and quantity,
remaining time until the end of the washing cycle,
information about malfunctions and error messages.


i 28 29	Temperature display Symbol Cold (lights up when active) Symbol Temperature (lights up when active)
ii 30 31	Spin speed display Symbol Rinse hold (lights up when active) Symbol Spin (lights up when active)
iii 32 33	Display for total washing time and/or delay end of washing Symbol ml (lights up when active) Symbol con. (lights up when active)

Link to the EU EPREL database

From 1 March 2021, information on energy labelling and ecodesign requirements is available in the EU EPREL product database.

The QR code on the energy label supplied with the appliance contains a web link through which you can find your registered appliance in the EU EPREL database.
Information regarding the performance of the product can also be found in the EU EPREL database, which is accessible via the link https://eprel.ec.europa.eu where you have to enter the model and product number; both are indicated on the rating plate on the appliance. On the website www.theenergylabel.eu you can find more detailed information about the energy label.

Keep the energy label in case it is needed in the future, together with the user manual and other documents supplied with this appliance.

Declaration of conformity

The company declares that the device with the function ConnectLife complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The detailed Declaration of Conformity can be found at the web address https://auid.connectlife.io on the page of your device among the additional documents.

Wi-Fi Network Requirements and Recommendations

Use a reliable wireless connection with sufficient signal strength. For all connection requirements, see the detailed instructions online.

INSTALLATION AND CONNECTION

Remove all packaging. When removing the packaging, make sure not to damage the appliance with a sharp object.

Before the first installation and during subsequent transport

Before using the washing machine for the first time, it is essential to install:

the rear hole plug on the back of the washing machine, and
the insulation strip at the bottom of the washing machine.

(depending on the model)

Install the insulation strip

(depending on the model)


The insulation strip is packaged separately and placed inside the washing machine drum.

Remove the transport securing device

Before the first use of the appliance, transport rods must be removed. A blocked washing machine may be damaged when it is switched on for the first time. Warranty shall be void in cases of such damage!

Move the hoses and undo the screws on the back of the washing machine. Remove the two angular pieces. Slide the angular pieces onto the grove in the blocking rod; before doing so, rotate the right angular piece to the opposite side. Use the angular pieces to rotate the blocking rods by 90° and pull them out. Cover the two holes through which the blocking rods were inserted with plastic plugs, and redo the screws that you undid in step 1. (The plastic plugs are supplied in the bag with the washing machine instruction manual.)

Install the rear hole plug


Insert the plug into the hole located at the lower left-hand side of the back of the washing machine. The rear hole plug can be found in the documentation bag.

Positioning the washing machine

Selecting the room

Floor on which the washing machine is placed must have a concrete base. It should be clean and dry; otherwise, the washing machine may slide. Also, clean the bottom surface of adjustable feet.

The washing machine must stand level and stable on a solid base.

If the washing machine is placed on an elevated stable base, the washing machine has to be additionally secured against tipping.

Leveling the appliance

Level the washing machine in longitudinal and traverse direction by rotating the adjustable feet.

Use a water scale and spanner No. 32 (for feet) and 17 (for the nut). The spanners are not supplied.

Washing machine installation clearances when installing in a room


Observe the clearances shown in the illustration.

The washing machine may not be in contact with a wall or adjacent furniture. For optimum washing machine operation, we recommend observing the clearances from the walls as indicated in the figure. In case of failure to observe the minimum required clearances, safe and correct washing machine operation cannot be ensured. Moreover overheating can also occur.

The washing machine must not be enclosed or built into furniture.

Connecting the washing machine to the water supply network

Connection to water supply


1	First, screw the rectangular end of the water inlet hose onto the valve on the rear wall of the washing machine (upper right). The inlet hose is supplied inside the washing machine drum.
2	STANDARD CONNECTION Attach the hose to the water tap by screwing it onto the thread (a).
3	AQUA - STOP CONNECTION Attach the hose to the water tap by screwing it onto the thread (a). If an internal tube or hose is damaged, a shut-off system is activated that cuts the water supply to the washing machine. In such case, the control glass (x) will turn red. Replace the water supply hose.

For normal washing machine operation, the pressure in the water mains should be between 0,05 and 1 MPa (0,5–10 bar). Minimum dynamic water pressure can be determined by measuring the water flow.

In 60 seconds, min. 10 L of water should flow from a fully open tap.

Tighten the water supply hose by hand, firmly enough for the hose to have a good seal (max. 2 Nm). After connecting the hose, the seal must be checked for any leaks. Do not use pliers or similar tools when connecting the hose as this could damage the nut thread.

Only use the water supply hose supplied with the appliance. Do not use any used or other hoses.

When connecting the water supply hose, make sure to connect it in a way that allows adequate and unobstructed water supply.

Connecting and securing the water discharge hose

Position the drain hose in a washbasin, bathtub, or directly into a drain (the drain pipe diameter must be at least 4 cm). The end of the drain hose may be no more than 100 cm (a) and no less than 60 cm (b) above floor level. It can be installed in three different ways.

The drain hose must not be disconnected, placed on the floor, or extended.

The drain hose must always be secured in the plastic holder.

Connecting the washing machine to the electricity supply

Before connecting the washing machine to the power mains, wait for at least 2 hours until it reaches room temperature.

We recommend using over-voltage protection overvoltage protection to protect the appliance in case of a lightning strike.

Connect the washing machine to a grounded power outlet. After installation, the wall outlet should be freely accessible. The outlet should be fitted with an earth contact (in compliance with the relevant regulations).

Information about your washing machine can be found on the rating plate (see detailed instructions online).

BEFORE USING THE APPLIANCE FOR THE FIRST TIME

Before switching on the appliance for the first time

First connection to a Wi-Fi network

Application ConnectLife

ConnectLife is a smart home platform that connects people, devices and services. The ConnectLife application includes advanced digital services and carefree solutions that allow users to monitor and control appliances, receive notifications from a smartphone, and update software (supported features may vary depending on your appliance and the region/country in which you are located).

Install the app

To connect your smart device, you need a home 2,4 GHz Wi-Fi network and a smartphone equipped with the application ConnectLife.

You can download the ConnectLife app for free from the Apple App Store® or Google Play™, or scan the code:

1	Install the ConnectLife app and create an account or log in to your existing account if you already have one.
2	In the ConnectLife app, go to the Add device menu and follow the instructions.

Unique QR code can be found on the warranty card or on the rating plate of the appliance.

3	After a successful connection, the appliance can be operated remotely via the application.

Do you have more questions?

Please visit us at www.connectlife.io or contact us at hello@connectlife.io.

WASHING PROCESS, STEP BY STEP (1–7)

Sort the laundry

You can find more detailed instructions online.

Sort the laundry by type of fabric, colour, soiling, and allowed washing temperature (see / ).

When sorting laundry, see the table below and pay attention to the labels on the laundry.

Washing

Bleaching

The number in the basket symbol means the maximum allowed washing temperature in (°C).

Bleaching is intended for refreshing and removing stains from textiles that are suitable for washing with bleach in a washing machine. Always follow the manufacturer’s instructions.

Normal wash

Delicate wash/very delicate wash

Bleaching with all types of bleaching agents

Hand wash only up to max. 40°C

Bleaching with oxygen-based bleaching agents

Washing is not allowed

Bleaching not allowed

Put the laundry in the washing machine and add the detergent and/or softener

Loading the washing machine

Adding detergents and fabric softeners

If you fill both compartments intended for the main wash (on the left side of the dosing container), excessive foaming will occur and the washing programme will not complete correctly.

Switch on the washing machine

Choose the washing program

Selecting a program on the control unit


Choose the programme by rotating the program selector knob to the left or to the right (depending on the type of laundry care required). See the chapter below. You can also select the programme in the ConnectLife app (turn the selector to Remote control and follow the instructions in the app.)

Set of washing programs

Legende v nadaljevanju

Explanation of symbols used below:

MaxLoad

Maximum load (kg)

Modes

Modes

SpinRPM

Spinning rate

DelayEnd

Delay end

Temperature

Temperature

DSA or ADS

Dose aid

Hladno pranje

Cold wash

AntiCrease

Anti crease

Prewash

Prewash

Extra Water

Extra water

Fast Faster

Fast + Faster

StainExpert

Stains

Steam

Steam

For more detailed descriptions of the functions, see the following chapters and the detailed instructions available online.

PRAZEN PRESLEDEK

Explanation of symbols for detergent types according to Regulation (EU) No. 1015/2010:

Univerzalno pralno sredstvo

Universal

Pralno sredstvo za občutljivo perilo in volno

For delicate laundry and wool

Pralno sredstvo za pisano perilo

For coloured laundry

Specialno pralno sredstvo

Special

PRAZEN PRESLEDEK

Tabela programov

Programs on the front panel

Program

Option of selecting additional functions

Eco 40–60 (AR brez *)

Eco 40-60*

kg FULL

9 kg

rpm MAX

1400

funkcije-ok

Temp 40-60

40°C–60°C

Uni+Color

Normally soiled cotton laundry that can be washed at both 40°C and 60°C together in the same cycle.

*	Test programme for compliance with the Commission Regulation (EU) No. 2019/2023 on ecodesign and Regulation No. 2019/2014 on energy labelling.

Cotton White

kg FULL

9 kg

rpm MAX

1400

VSE funkcije-ok

Temp 20-90

20°C–90°C

Uni+Color

Use Cotton white programme to wash normally soiled cotton linen. Choose between different washing temperatures. Spinning speed can be set to your preference. Programme duration and amount of water will be adjusted to the amount of laundry. Select Prewash or Extra waterl function for heavily soiled garment. For customers with allergies, we recommend the Extra rinse function for better rinsing of the laundry.

Cotton Colour

kg HALF

4,5 kg

rpm 1200

1200

VSE funkcije-ok

Temp cold-60

–60°C

Uni+Color

This programme is used for washing coloured laundry using special-purpose detergents for coloured laundry. We recommend turning dark garments inside out.

Mix|Syntetics

3,5 kg

rpm 1200

1200

VSE funkcije-ok

Temp cold-60

–60°C

Color

The Mix / Synthetics programme is adapted for clothing made of synthetic and mixed fibres or viscose and for easy care of cotton laundry.

Wool|Handwash

2 kg

rpm 800

800

funkcije

Temp cold-40

–40°C

Wool+Special

Gentle washing programme for washing wool, silk, and clothes that require manual washing. Maximum temperature is 40°C. This programme has a short spinning cycle. Top spinning speed available is 800 rpm.
Do not use conditioner with this programme!

Power 29/39

Power 29’

2 kg

rpm 1200

1200

funkcije

Temp 40

40°C

Color+Wool

A programme for smaller loads of lightly soiled laundry.

Speed 14

Speed 14'

1 kg

rpm 1000

1000

funkcije

Temp 30

30°C

Color

A programme for cotton garments that have hardly been worn or are only very lightly soiled.

Ultra clean (Drum Clean)

Ultra clean

/

rpm MAX

1400

funkcije

Temp 90

90°C

This programme is used for cleaning the drum and removing the residue of detergent and bacteria. To select the programme, rotate the selector to the left or to the right to the Ultra clean (Self-cleaning programme) position. Other extra functions cannot be selected.

The drum must be empty. Do not add detergent or softener! You can add some spirit vinegar (approx. 2 dl) or sodium bicarbonate (1 tablespoon or 15 g) for effective descaling. We recommend that you use the programme at least once a month.

You can add the agents to the main wash compartment or to the drum.

Rinse&Softening

kg FULL

9 kg

rpm MAX

1400

funkcije

/

This programme includes two cold rinses and a short spinning cycle. The programme is suitable for laundry that only needs rinsing.

Spin&Drain

kg FULL

9 kg

rpm MAX

1400

funkcije

/

Use the programme when you only wish to spin the laundry or to drain out the water from wet laundy.

Bedding

kg HALF

4,5 kg

rpm 1200

1200

VSE funkcije

Temp 30-90

30°C–90°C

Uni+Color

This programme is used to wash bedding, pillows, and larger items. Weekly wash of your bedding will remove skin residue and mites.

Sports

3,5 kg

rpm 1000

1000

funkcije

Temp cold-40

–40°C

Color+Wool

This programme is suitable for washing clothing with membranes, waterproof clothing, and breathable clothing, requiring simple care. It is suitable for sportswear made of mixed materials. It combines low temperature with gentle tumbling.
Do not use conditioner with this programme!

Allergy Safe

kg HALF

4,5 kg

rpm 1200

1200

VSE funkcije

Temp 40-90

40°C–90°C

Uni+Color+Special

This programme is used to wash normal to heavily soiled clothes that require special care, such as clothes for people with highly sensitive skin or skin allergies. We recommend turning the garments inside out as this will also thoroughly wash out the skin and other residues. You can also select the option to wash at maximum temperature and maximum spinning speed. Set temperature will be maintained for a longer time period than on conventional programmes in combination with intense agitation.

Pets

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 40

40°C

Uni+Color+Wool

During this programme, pet hair is removed from your garments. The washing programme includes an automatic prewash and additional rinses.

After the washing programme completion, clean the glass on the washing machine door and the pump filter in which pet hair could be trapped. We recommend running the Ultra clean programme after the wash, in order to thoroughly remove any pet hair from the washing machine.

Remote control

Use the Remote control programme to remotely control your appliance (using your phone).

In the application, you can also select additional programmes and some additional settings.

Use the Remote control programme to remotely control your appliance (using your phone).

It is possible to select all programs and functions that are available for a specific program of your appliance (see sections / and / Remote control).

In the application, you can also select additional programmes and some additional settings.

The following washing programmes can be selected in the ConnectLife app:

Pillow

New Clothes

Dark Clothes

Plush Toys

Kids Wear

Swimwear

Waterproof

Tights / Stockings

Lingerie

Kitchen Towels

Bleaching

Activewear

Curtains

Easy Care

Steam Refresh

Baby

Jeans

Fabric Care

Shirts

Shoes

Casual Wash

Program

Option of selecting additional functions

Pillow

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 40

40°C

Uni+Color+Wool

Use this programme to wash blankets, coats, vest or jackets. Insert garments into the machine so that they do not touch the rubber seal or the glass.

New Clothes

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 30

30°C

Uni

A programme ideal for the initial wash of new garments that may release dye or contain textile finishing residues.

Dark Clothes

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 40

40°C

Special

This programme helps maintain the intensity of dark colors.

Plush Toys

kg HALF

4,5 kg

rpm 1000

1000

funkcije

Temp 30

30°C

Uni

A programme for fluffy toys, gentle and effective.

Kids Wear

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 60

60°C

Vse

A programme designed for effective stain removal and enhanced hygiene. Ideal for everyday children’s clothing.

Swimwear

kg HALF

4,5 kg

rpm 1000

1000

funkcije

Temp 30

30°C

Special

A programme for your delicate swimwear, remove the salt and prolong the fabric.

Waterproof

2.5 kg

2,5 kg

rpm 800

800

funkcije

Temp cold

Color+Special

A programme for impregnating garments with special agents that increase water resistance.

Tights/Stockings

Tights / Stockings

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 30

30°C

Uni

An extra-gentle programme for fine and stretchable fabrics.

Lingerie

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 30

30°C

Wool+Special

A gentle programme for fine, lace, and stretchable fabrics. The use of a laundry bag is recommended.

Kitchen Towels

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 60

60°C

Uni+Color

A programme designed for heavily soiled kitchen textiles such as cloths and towels.

Bleaching

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 60

60°C

Special

This programme is designed for use with chlorine-free bleaching agents. It helps remove stubborn stains and restore the brightness of light-colored fabrics. Suitable only for textiles labeled as bleach-resistant.

Activewear

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 30

30°C

Color+Wool+Special

Programme suitable for functional fibers and elastic materials commonly used in sportswear.

Curtains

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 30

30°C

Wool+Special

A gentle programme that uses a higher water level and minimal mechanical action to prevent creasing and damage to delicate decorative fabrics.

Easy Care

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 40

40°C

Vse

A programme for clothing made of synthetic and mixed fibres, and for simple care of cotton. Carefully read the washing instructions. Washing temperature can be set up to 60 °C, and spinning speed can be set up to 1200 rpm.

Steam Refresh

1.5 kg

1,5 kg

funkcije

/

The programme allows clothes to be softened and disinfected. Steam refresh reduces or eliminates the need for ironing. After steam refresh the laundry may be slightly damp or contain minor traces of water.

BabyTR-isG400 or isG600

Baby

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 60

60°C

Vse

This programme is used for washing clothes that require special care. Such as baby clothes or clothes for people suffering from skin allergies.

ShirtsTR-isG400 or isG600

Shirts

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 30

30°C

Vse

This programme washes the collars and cuffs without wrinkling them. The wash takes place at a low temperature, with a greater amount of water and gentle tumbling.

JeansTR-isG400 or isG600

Jeans

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 40

40°C

Color+Wool

A programme for denim and jeans. Wash inside out.

ShoesTR-isG400 or isG600

Shoes

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 30

30°C

Wool

A programme fro trainers without leather. Coarse soiling should be brushed off first before washing. The washing programme includes an automatic prewash. A small additional load of towelling or cleaning cloths increases the cleaning performance and reduces noise. Do not use fabric conditioner. Follow the instructions on the care label.

Fabric CareTR-isG400 or isG600

Fabric Care

kg HALF

4,5 kg

rpm 800

800

funkcije

Temp 40

40°C

Vse

The programme is ideal for delicate fabrics, as it reduces wear and tear by washing them gently. Fabrics retain their quality and their life is extended.

Casual WashTR-isG400 or isG600

Casual Wash

kg HALF

4,5 kg

rpm 1200

1200

funkcije

Temp 30

30°C

Vse

A programme ideal for lightly soiled casual wear, helping maintain color and fabric quality with optimized energy efficiency.

Maximum or nominal load applies to laundry prepared pursuant to the IEC 60456 standard.

Select the additional functions

Izbira funkcije

Once you have selected a washing programme, you can also choose and adjust additional functions for certain programmes.
Some functions can also be selected and adjusted later, while the programme is running.

This is done in two or three steps:
- selecting the function,
- setting the function level, if the function allows it,
- activating the function.

If you do not want to select additional functions, press the Start/Pause button.

1	Use the selector knob to select the desired programme.
2	Press the button to enter the function selection menu. The functions available for the selected programme will then be partially illuminated.
3	Press the buttons located next to the button (this allows you to scroll through the available functions) until the symbol of the desired function starts flashing.
4	The symbol of the desired function flashes.
5	Press the button to confirm the selected function; the symbol of the selected function lights up fully.
6	The function is activated by pressing the Start/Pause button. During the washing programme, all selected functions will be fully illuminated.

You can directly select, set and confirm some additional functions and settings using the keys.

You can also select additional programs in the app ConnectLife. Follow the instructions in the app.

If you press and hold the button for more than three seconds, you will enter the Wi-Fi settings (applies when Remote control has been selected using the selector knob).

If you select the Stains option, the Prewash option becomes disabled.

Nabor funkcij

A set of additional washing functions.

For a more detailed description of the functions, see the detailed instructions available online.

	TEMPERATURA PRANJA Temperature Changing the temperature for the selected program.
	OŽEMANJE Spin (spinning rate/pump stop/drain) To adjust the spinning rate.
	HITRO PRANJE Fast wash (shorter washing time) For quick washing of laundry.
	DELAY END Delay end Function for delaying the end of the wash cycle
TR-isG600	NAČIN PRANJA Modes (Washing mode) To select the washing mode.
TR-isG600 or isG800	MADEŽI Stains (stain removal) For removing different types of stains.
	PREWASH Prewash Washing heavily soiled laundry, particularly with stubborn superficial stains.
	WATER+ Extra water (additional water/high water level) Function for washing laundry with a larger amount of water on some programmes.
	PARA Steam (steam desinfection) A function for disinfecting the laundry.
TR: not (isADS or isG400)	DOSE AID Dose aid (information on dosing liquid detergent) Information on recommended amount of powder and liquid detergent, according to the selected settings and the amount
	ANTI CREASE Anti crease (anticrease) A function to loosen and reduce creasing of laundry.
	OPTIMIRANJE ČASA Optimizing washing time In the early stage of the washing programme, the washing machine uses advanced technology to detect the amount of laundry. After load detection, the washing machine adjusts the programme duration.

Start the washing programme

Close the washing machine door and start the washing programme by pressing the Start/Pause button on the right side of the display.

Complete the washing cycle

At the end of the wash, an audible signal sounds and (End) is displayed on the screen. 5 min after the program ends, the appliance switches to a low-power standby or sleep mode.

APPLIANCE SETTINGS AND ADJUSTMENTS

There are a few additional settings that can be set on the appliance. This will allow you to further customize the device to your personal use and needs.

For setting up the personal menu and saving programs and functions, see the detailed online instructions.

The individual options for setting up the appliance are listed below.

Settings using a single button press

	VKLOP/IZKLOP ZVOKA Sound On/Off Option to switch the sound on or off. If the sound is switched off, there will be no audible signal at the end of the washing programme.
	REMOTE CONTROL Remote control Function for remote control.
	OTROŠKA ZAŠČITA Child Lock A safety feature. Press the button to enter the Child Lock setting selection menu. The function symbol is fully illuminated. Use the buttons to switch between the two options and confirm the selected option with the button. To switch off (deactivate) the child lock, press button 3 sec for second. Animation 3-2-1 will start. At the end of the animation, the function turns off (is deactivated).
	SAVING PROGRAM SETTINGS Settings saved Function to save your settings for selected programs and functions.

Settings using a combination of two buttons pressed simultaneously

To enter the settings, select a washing programme and simultaneously press and hold and for at least 3 seconds, until the 3-2-1 animation has completed.

By pressing and , you can navigate through the available user settings.

When you are in the desired setting, move between the setting levels by pressing the button.

Press the button to save and exit.

Press to scroll through the available user settings.

prikaz	VKLOP/IZKLOP IN IZBIRA JAKOSTI ZVOKA Sound On/Off and selection of the sound level Press the button to select the sound level or to switch the sound off. If the sound is switched off, there will be no audible signal at the end of the washing programme.
prikaz	SVETLOST ZASLONA Display brightness Option to adjust the brightness of the symbols illuminated on the display.
prikaz	TRDOTA VODE Water hardness Option to set the water hardness.
prikaz	TOVARNIŠKE NASTAVITVE Factory reset Delete all settings and return to the factory settings. If you do not want to return to the Factory reset, press to exit.
prikaz	PREGLED ZADNJIH TREH NAPAK Overview of the last three errors Option to review the last detected errors of the washing machine.
prikaz	SKUPNO ŠTEVILO CIKLOV Total number of cycles Option to review the completed cycles of the appliance.

CLEANING AND MAINTENANCE

Before cleaning, unplug the washing machine from the power mains.

Cleaning the dispenser tray

Cleaning the water supply hose, detergent dispenser housing, and rubber door gasket

Cleaning the pump filter

We recommend regular cleaning of the pump filter once a month. When washing very fleecy, very dirty or old laundry, do it more often.

TROUBLE-SHOOTING

Display Message Table

Warnings/information for the user, which can be indicated on the display unit, may include the following:

AC	Anti crease function that you have selected as a part of the washing programme is activated and in progress The Anti crease and End signs will alternate on the display unit. To stop the Anti crease function, press the Start/Pause ON/OFF button.
	Washing machine standing by, ready to resume the washing programme On the display, the time remaining until the end of the wash and the Start/Pause button flash. To resume the washing programme, press the Start/Pause button.
	Preparation for unlocking the door Signal lights will flash on the display unit. Wait for the process to finish. If no errors are shown after the process, a new cycle can be run. Water is being drained. Wait for the door to unlock.
	Displaying the number of completed wash cycles Information about the number of washing cycles performed is displayed on the display for 3 seconds if you unplug the power cord from the power supply (after setting the selector to position Off), wait 10 seconds and then plug the power cord back in. After 3 seconds, the appliance switches to standby mode. The number of cycles performed is also available in the user settings menu. See chapter / / Total number of cycles.
CLF	Water drain system alert Display of warning CLF. After the washing programme is complete, the signs CLF and End will alternate on the display unit. Alert about reduced water flow in the pumping stage. Check the following: is the pump filter clean, is the drain hose clogged, is the drain clogged, if the drain hose is placed below the maximum and above the minimum height (see chapter / / ).
CLn	System warning to run the *Ultra clean* After the washing programme is complete, the signs CLn and End will alternate on the display unit. In case of a CLn warning on the display after washing, proceed as follows: clean the dosing container, clean the water supply hose, detergent dispenser, and rubber door gasket, clean the pump filter (see chapter ) and run the self-cleaning program Ultra clean (see chapter ). Self-cleaning programme is used to clean the drum and to remove detergent residues and bacteria. The drum must be empty. Do not add detergent or softener! You can add some spirit vinegar (approx. 2 dl) or sodium bicarbonate (1 tablespoon or 15 g) for effective descaling. We recommend that you use the programme at least once a month or whenever the warning appears CLn.
FD	Warning by the system for detecting excessive foaming during the washing programme After the washing programme is complete, the signs FD and End will alternate on the display unit. In case of excessive foaming in the washing machine or leak of foam through the detergent dispenser tray, the washed laundry has to be rinsed thoroughly with a large amount of water. Choose a washing programme, but do not add any detergent. We recommend choosing the Rinse & Softening programme. Decrease the amount of detergent added.
PF	Power supply failure warning (PF) The system detected a power supply failure during the washing programme progress, which affected functional execution of the washing programme.
PF/End	Power outage notification (PF/End) (Power failure) Upon completion of the washing cycle, End and PF will alternate on the display unit. This informs the user about a power supply failure and on the effect on the execution of the washing programme. The washing program continues where it was interrupted and then ends successfully.
ULo	Warning – U:Lo (voltage below 180 V) A prolonged drop of voltage to below 180 V was detected, which can affect the washing machine operation. Check the power supply network to which your washing machine is connected. Unresponsive display unit and all buttons Unplug the power cord from the outlet. Check if the supply voltage is suitable for the washing machine (220–240 V); then, plug the power cord back into the outlet and switch on the washing machine.
UHi	Warning – U:Hi (voltage over 260 V) A prolonged voltage surge to over 260 V was detected, which can affect the washing machine operation. Check the power supply network to which your washing machine is connected.

The following lists all the errors that the user can see on the user interface.

Er 00	Incorrect settings Restart the program.
Er 01	Temperature sensor error Inlet water too cold. Repeat the washing program.
Er 02 dor	Door lock error Make sure the washing machine door is closed. If you hear an acoustic signal after pressing the Start/Pause button, it means that the door of the washing machine is not closed. Close the washing machine door. Unplug the power cord from the outlet; then, plug the power cord back into the outlet and switch on the washing machine.
Er 03	Water filling error Check the following: the suitability of the drain height, whether the drain hose is secured to the washing machine housing, is the water inlet valve open, whether the filter on the inlet hose and on the water valve is clean, is the water supply hose deformed (clipped, clogged etc.), is the pressure in the water mains between 0,05 and 1 MPa (0,5–10 bar), in 60 seconds, min. 10 L of water should flow from a fully open tap, Then, press the Start/Pause button to resume the program.
Er 06	Water heating error Restart the program.
Er 07	Water draining error Check the following: is the pump filter clean, is the drain hose clogged, is the drain clogged, if the drain hose is placed below the maximum and above the minimum height (see chapter / / ), whether the pump impeller is not blocked (the impeller must rotate freely); then, press the Start/Pause button again. Excessive amount of detergent Too much detergent may cause excessive foaming in the drum. See description for Fd.
E9.1 Er 09	Water leak detected in the washing machine area Turn off the washing machine and turn it back on. Inspect the exterior of the appliance. If you do not observe any leaks, you can continue to use the washing machine.
Er 10	Water level sensor error Unplug the power cord from the socket, wait 1 min, then plug it back in and switch on the washing machine. Vent the appliance. Do this by draining and cleaning the washing machine filter and cleaning the wall-mounted trap.
Er 11	Water overflow If there is water in the drum that exceeds a certain level, and an error is reported on the display unit, the washing program will be interrupted and water will be pumped out of the washing machine. Restart the program. If there is water in the drum that exceeds a certain level, and an error is reported on the display unit, while the washing machine continues to add water, close the water tap and call a service technician. Excessive amount of detergent Too much detergent may cause excessive foaming in the drum. See description for Fd.
Er 12.01	Phase current exceeded The washing machine detected an exceeded phase current in one of the phases and therefore stopped operation. Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 minute. In the meantime, check whether the drum is overloaded or unevenly loaded; if necessary, redistribute the laundry or remove some of it. Reconnect the appliance and start the program again.
Er 12.4	Phase current exceeded – operation disabled Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 minute. Reconnect the appliance and start the program again.
Er 12.5	Rotor blocked The motor is unable to rotate, which prevents the program from operating normally. Switch off the washing machine and check whether the drum is mechanically blocked (an object in the drum, a trapped piece of laundry, etc.). Remove the obstruction. Turn the machine back on and start the program. If the error occurs again, the motor or drive assembly may be faulty.
Er 12.8	Electronics communication failure in the washing machine Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 minute. Reconnect the appliance and start the program again.
Er 12.12	Wrong software version The washing machine has detected a mismatch or invalid software version in one of the modules. Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 min. Reconnect the appliance and start the program again. A software update or reinstallation is required.
Er 12.17	Motor is not connected The washing machine does not detect a connection between the motor and the control module. Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 minute. Reconnect the appliance and start the program again. If the error occurs again, the connection to the motor is likely broken.
Er 13.3	Load detected during the programme (Ultra clean) Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 minute. Meanwhile, remove all items from the drum. Reconnect the appliance and start the program again.
Er 22	Error while locking the door The door cannot be locked. The door locking mechanism is not working properly, so the appliance cannot start the programme. Check that the door is properly closed and nothing is blocking the latch. Disconnect the washing machine from the power supply (unplug the power cord) and wait for 1 minute. Reconnect the appliance and start the program again. If the error occurs again, the door lock mechanism or door switch may be faulty.
Er 23	Error while unlocking the door Door is closed, but it cannot be unlocked. Unplug the power cord from the socket, wait 1 min, then plug it back in and switch on the washing machine.
	The appliance cannot be controlled remotely Appliance remote control is not activated or enabled. Check if the Wi-Fi symbol on the appliance is lit, and turn the selector to position Remote control .
	The appliance will not connect to the Wi-Fi network The appliance cannot find your Wi-Fi network. Check whether 2.4 GHz network is activated on your router and whether the Wi-Fi signal at the appliance is strong enough.

If the problems persist despite observing the advice above, call an authorized service technician.

In the Member Sctates of the European Union, Iceland, Liechtenstein and Norway, consumers have the right to choose an authorised or independent repairer at their own discretion. However, if an independent repairer is chosen, the retailer or manufacturer does not assume responsibility for potential product safety risks or for infringements of intellectual property rights resulting from interventions performed by the independent repairer, nor for any possible loss of warranty rights arising from objective or legitimate factors related to improperly performed repairs..

Service

When you contact a service centre, please state your washing machine's type, code/ID, model number, and serial number.

Washing machine type, code, model, and serial number can be found on the rating (type) plate on the inner side of the washing machine door.

A more detailed description of the rating plate can be found in the detailed instructions available online.

Splošna napisna tablica

MAJHEN PRESLEDEK

1	–	type designation of the appliance
2	–	model designation of the appliance
3	–	the article number/service index (you will need them when contacting customer service)
4	–	serial number of the appliance (you will need them when contacting customer service)
5	–	unique QR code (required when connecting the appliance to a Wi-Fi network)

In case of a failure, only use approved spare parts by authorized manufacturers.

Repair or any warranty claim resulting from incorrect connection or use of the washing machine shall not be covered by the warranty. In such cases, the costs of repair shall be charged to the user.

Warranty

The warranty does not cover consumables, minor deviations in colour, increased noise that results from appliance age and which does not affect the functionality of the appliance, and aesthetic defects on components, which do not affect the functionality and safety of the appliance.

The warranty does not cover the errors or failures resulting from disturbances from the environment (lightning strike, power grid failures, natural disasters etc.).

Report any malfunction to your local call centre or web address; all information can be found in the enclosed warranty statement. Contact details of your authorised service centre are available in the warranty statement supplied with the appliance and on the website by scanning the QR code on the rating plate.

Some simple faults described in the chapter / can be fixed by the user himself by taking into account the instructions without risk to their own safety and without affecting the warranty conditions.

Spare parts

Functional spare parts for the washing machine you purchased will be available for 10 years. During this time, original spare parts will be available to ensure the correct operation of your appliance.
A list of spare parts and repair tips in accordance with the current Ecodesign Directive can be found by scanning the QR code located on the inside of the door of the washing machine. Or on the following link: https://auid.connectlife.io.

RECOMMENDATIONS FOR WASHING AND ECONOMIC USE

Wash heavily soiled laundry in smaller amounts, with more powder detergent or with a pre-wash cycle.

With slightly soiled laundry, we recommend a programme without a pre-wash cycle, use of shorter programmes (e.g. Speed 14') and a lower washing temperature.

We recommend avoiding washing very small amounts of laundry as this will lead to excessive use of energy and poorer washing machine performance.
You can save energy and water by filling up the washing machine to the capacity specified by the manufacturer for each programme.

At higher spinning rates, there will be less residual moisture in the laundry. As a result, drying in a tumble dryer will be more economical and faster.

Detergents carrying the environment protection label are less harmful to the environment.

If you wash at low temperatures and/or with liquid detergents, there is a risk of developing microorganisms and an unpleasant odour in the washing machine. Leave the washing machine door open after each wash to allow the appliance to dry. If you detect an unpleasant odour, run the Ultra clean programme.

For tips on optimal laundry results, preventing and removing limescale, and stain removal tips, see the online instruction.

CONSUMPTION VALUES

The provided information is in accordance with EU Regulation 2019/2023. The values indicated for programmes other than Eco 40-60 have been determined in accordance with the applicable standard EN60456.

Legenda nad tabelo

Explanation of symbols used below:




	Energy efficiency class		Water consumption (L per cycle) (1)


	Washing temperature (°C)		Maximum temperature (°C) 5 min (1)


	Rated capacity (kg)		Remaining moisture content (%) (1)


	Programme duration (h:min) (1)		Spin speed (rpm) (1)


	Energy consumption (kWh per cycle) (1)

TABELE PORABNIH VREDNOSTI

PRAZEN PRESLEDEK (z dodanimi rezervami)

Program

i	Eco 40-60 (2)

A

40-60

kg FULL

9 kg

03:30

0,800

61

31

53

1320

kg HALF

4,5 kg

02:50

0,230

48

22

1400

kg QARTER

2,5 kg

02:35

0,200

25

24

1400

ii	Cotton White

20

kg FULL

9 kg

03:46

0,31

96

20

54

1400

	Cotton White

40

kg FULL

9 kg

04:48

1,42

98

42

54

1400

iii	Cotton White

60

kg FULL

9 kg

04:28

2,21

108

62

54

1400

iv	Mix\|Syntetics

30

3,5 kg

02:45

0,52

57

32

31

1200

v	Speed 14'

30

1 kg

00:14

0,10

16

30

63

1000

vi	Cotton White

90

kg FULL

9 kg

04:28

3,16

113

80

54

1400

Legenda pod tabelo

i	the eco 40-60 programme at the rated capacity, half of the rated capacity and a quarter of the rated capacity;
ii	the 20 °C programme at the rated capacity for this programme;
iii	one cotton programme at nominal temperature higher than or equal to 60 °C (if present) at the rated capacity for this programme;
iv	one programme for other textiles than cotton or a mix of textiles (if present) at the rated capacity for this programme;
v	one programme for the quick washing of lightly soiled laundry (if present) at the rated capacity for this programme;
vi	one programme for heavily soiled textiles (if present) at the rated capacity for this programme;
(1)	Due to the influence of water pressure, hardness, and inlet temperature, the type, quantity, and soiling of the laundry, the detergent used, power supply, and selected functions, the actual values may differ from the specified values.
(2)	Test program with cold water (15°C) in accordance with the EU Directive on Eco-design and the EU Regulation on Energy Labeling.

Notes

SAFETY PRECAUTIONS

knjiga Carefully read the instructions for use before using the washing machine.

Please, do not use the washing machine without reading and understanding these instructions or use first.

These instructions for use of a washing machine are supplied with different types or models of washing machines. Therefore, they may include descriptions of settings or equipment that are not available in your washing machine.

Instructions for use are available on our website at www.gorenje.com.

Use in accordance with regulations

MAJHEN PRESLEDEK

Failure to observe the instructions for use or inappropriate use of the washing machine may result in damage to the laundry or the appliance, or injury to the user. Keep the instruction manual handy, near the washing machine.

This appliance is intended to be used in household and similar applications, such as:

staff kitchen areas in shops, offices and other working environments;
farm houses;
by clients in hotels, motels and other residential type environments;
bed and breakfast type environments.

This appliance must not be used in:

areas for communal use in blocks of flats,
in open spaces or outdoors.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Installation and connection

MAJHEN PRESLEDEK

The washing machine may only be used with the factory-installed power cord.

To avoid danger, a damaged power cord may only be replaced by the manufacturer, a service technician, or an authorized person.

Do not connect the washing machine to power mains using an external switching device such as a programme timer, or connect it to power mains that is regularly switched on and off by the power supply provider.

Follow the instructions for correct installation of the Gorenje washing machine and connection to the water and power mains (see chapter ).