Measurements according to EN60350-2

Following is some advice on rectifying some common problems.

Information for consumer and test institute

Information about your product can be found at www.asko.com, where you will also find a link to the European Product Database for Energy Labelling, EPREL. Or else visit https://eprel.ec.europa.eu directly.

We hereby declare that our products satisfy the applicable European directives, orders and regulations, as well as the requirements stated in the referenced standards.

Sustainable materials have been used during the manufacture of this appliance. This appliance must be disposed of responsibly at the end of its service life. Ask your local authorities for more information about how to do this.

Recycle as electrical waste!

• This appliance should only be connected by a registered installer.

• Prior to installation, ensure that the local distribution conditions (voltage, frequency, nature of the gas and gas pressure) and the adjustment of the appliance are compatible.

Electrical connection Class I - 220-240 V - 50/60 Hz - max 3500 W.

• This appliance must be earthed.

• The voltage, frequency, power, type of gas and the country for which the appliance has been designed are shown on the appliance rating plate.

• The electrical connection must comply with national and local regulations.

• If a stationary appliance is not fitted with a supply cord and a plug, or with other means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under overvoltage category III conditions, the means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. Using an omnipolar switch with a contact separation of at least 3 mm fitted in the supply cable will fulfil this requirement.

Gas connection 1/2” ISO 228 / ISO 7-1 / EN 10226-1 (1/2” ISO 228 / 1/2” ISO 228 FR only).

• The gas connection must comply with national and local regulations. See appliance label for technical gas data.

• This appliance is not connected to a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.

• We recommend that the gas hob be connected by means of a fixed pipe. Connection using a specially designed safety hose is also permitted.

• The pipe behind the oven must be made entirely out of metal.

• A safety hose may not be bent and must not come into contact with moving parts of kitchen units.

• The gas supply valve must always be placed in an easily accessible position.

• The walls and the worktop surrounding the appliance must be heat resistant up to at least 105 °C.

• The bottom kitchen element must be equipped with a built-in horizontal shelf at a distance of not less than 15 cm from the bottom surface of the worktop. The space between the shelf and the cooktop must be empty and may not be used for the storage of utensils.

For converting to a different type of gas, the nozzles have to be changed.

The values are also marked on the nozzle.

1. Remove pan supports, burner heads, crowns and covers (see pictures A1 and A2).

   Pull off the control knobs vertically.

2. Use the socket (T1) or open-end spanner (T4) to remove the old nozzles and place the new nozzles inside the burner cups (see pictures A1 and A2).

   

Depending on the gas type to which the appliances will be converted, there are two ways to adjust the by-pass screws.

Please check the conversion table in the column “Modification” if the by-pass screws have to be screwed completely in (see action 3A), replaced by a different by-pass screw (see action 3B) or adjusted (see action 3C).

The values are also indicated on the top of the by-pass screws. The by-pass screws can be reached from the top of the hob when the knobs are removed (B2).

3A. Screw the by-pass screws (3) of all gas taps completely in by using the flat-blade screwdriver (T2).

3B. Remove the by-pass screws by using the flat-blade screwdriver (T2) and the nose pliers (T3). Place the new by-pass screws with the nose pliers and screw the by-pass screws of all gas taps in, by using the flat-blade screwdriver.

3C. Adjust the by-pass screws (3) of all gas taps by using the flat-blade screwdriver (T2) until a stable flame is established with a minimal gas flow. Please check if the flame is stable in the cold and hot conditions of the burner.

When the appliance is connected to the gas supply, use leak test spray to check the gas tightness.

1. Seal the injector.

2. Open the gas tap. Attention: press and open the tap to override the thermo-electric safety device and keep it pressed down.

3. Spray leak test spray over all gas connections and check for gas tightness.

4. Repeat for every burner.

1. Reinstall the knobs, burner parts and pan supports.

2. Check if the appliance is connected to the correct gas type and pressure.

3. Open the main gas valve.

4. Insert the plug into the power socket.

Sustainable materials have been used during the manufacture of this appliance.

The appliance packaging is recyclable. The following may have been used:

• cardboard;

• paper;

• polyethylene film (PE);

• CFC-free polystyrene (PS-rigid foam);

• polypropylene tape (PP).

Dispose of these materials in a responsible manner and in accordance with government regulations.